How to Cut Open an Egg

Preface: You may injure or kill your baby while cutting open an egg. Only cut open an egg if you are sure it is past the time to hatch and it will not hatch on its own. If you do not know how to determine this you must ask for advice. It is often difficult to balance patience and action. Remember that some babies are “just not meant to be”.


You may need to cut a chameleon egg if it has sweated and shrunk but there are still no slits -- especially if you have already lost one or two eggs and the others have sweated then stopped progressing. There also may be a problem with an egg if its other clutchmates have hatched perfectly but it seems stuck.

I give a shrunken egg 48 hours MAXIMUM to either sweat and shrink more, or slit on its own. If nothing is happening after 48 hours I always cut. I often cut after 24 hours or less. Others are much more patient:

Scott85;480838 said:
I have a clutch of faly's hatching out right now too. The first one to come out sweated for 2 days then pipped but blew out both ends of the egg. After two days of sitting in the shell I freaked out and cut the shell off of him. He wasn't moving and still had a large yolk on him, I feared the worst. Figuring I had jumped the gun I got scared and left him in the vermiculite, trying to put the shell around him the best I could. After another day and a half like that, spraying him to keep him moist, he woke up and is doing well. It dont look good for that little guy, but give em a lil bit before you give up on him.

If I failed to observe the sweating and shrinking period, and stumble upon a clutch with several WRINKLED eggs, I will wait 0-6 hours before cutting, depending upon appearance (shape, color, wetness -- an egg that is too far gone will begin to break down and brown). I cut these eggs open much sooner because once an egg is wrinkled it will loose its ability to provide oxygen to the baby inside. Here is how it is done:

A SHARP blade is a must. I have a very thin, flat knife like a mini fillet knife but a razor blade or scalpel may work fine for you. It is good to also have handy tweezers, a hangnail clipper or other small surgical type scissor (different from a regular nail clipper) or other small surgical type scissor, and some paper towels. You will want good lighting. You may want to work over a separate bin containing soft dry vermiculite to catch the egg, and put the rest of the eggs back in the incubator.

If the egg is shrunken but still round and firm, my technique is to lightly slice a horizontal slit across the top of the egg without pushing down much at all (it is like you are beginning to open a lid on the egg). Your objective at this point is to barely break through the surface.

I cut mainly while pulling the blade towards my body, using minimal pressure and just letting the edge do all the work. If you find yourself pushing down and creating a dent, you blade is too dull. Also, the blade must be so SHARP that you do not need to stabilize the egg much at all with your other hand. Squeezing the egg too hard is dangerous because it will push neonate towards the top and thus the blade.

While cutting you may find that the shell is like several layers of skin – you cut through one and there is still another thin layer below. Keep cutting but reduce the pressure as you get closer.

Once you have created an opening and some fluid leaks, immediately STOP slicing. You can use a paper towel to blot some fluid so you can see things clearly.

Turn knife upside down and insert tip (or switch to scissors or cliper) into your hole so the dull back of the knife will face the baby and the blade will touch only the inside surface of the shell, coming up from underneath.

Push or lift the blade into the shell and make another tiny cut like a 1/2 mm nick. A specific hangnail clipper may be easier at this point because you can snip at the opening until it is a good size.

If there is an extra flap of shell now, you can grip it with tweezers -- just make sure there is not an arm or tail in the way. This will give you control without squeezing the neonate.

Anyway, insert knife again, make sure there is no body part between blade and shell, and repeat once or twice. The line you cut does not need to be straight. If you are using clippers it will most likely be jagged.

Opening can be surprisingly small, like 3mm.

Look for a nostril. If you can see it clearly and it is unobstructed you may be DONE FOR NOW. Place the egg back the incubation container by pressing your finger into the media to make a hole and place the egg back in with the cut hole facing up.

A clear airway is necessary to finish the job. If there is fluid in the way you can dab it with the corner of a folded paper towel. Do not squeeze out the fluid. Also, keep lint out (q-tips are too linty) and remove any seriously obstructive incubation substrate.

If you cant tell what you are looking at, cut a bit more. The tail is usually wrapped around the body and the tip may be at the same end of the egg as the head. If all you can see is a chameleon butt you have the wrong side of the egg and you may need to make a slit up the back side and try to retain as much fluid as possible.

At this point you have done all you can do. Once a nostril is clear, leave the baby in the fluid in the egg and do not disturb it. Keep it as moist as any other egg. If it is dead you will know soon enough. Good luck to both you and the baby!

Some final tips:

Avoid the yolk sac. Leave it intact at all times.

Keep the cut egg in high humidity – the fluid must not dry out. The original incubation container is usually the best place.

Pause occasionally and watch for movement from the baby. That said, it will usually not move at all, even if it is perfectly alive.

If using a razorblade you can place several layers of tape on the spine to create a grip.
  • Like
Reactions: Nelius


Yup, I hate waiting to open up presents;) Seriously though I probably cut early in some cases but I figure why wait? I just have a strong instinctive feeling some times and I act on it.
So i have a panther egg that has piped and leaked a sticky clear fluid. The egg has shrunk and dimpled. I can see the very tip of what id assume is the face. Its been this way for almost 3 days with no change but the area around it seems to still be from the clear liquid. Should i try cutting the opening a little bigger? This is my first egg to hatch so im completely new to this. Thanks!

Blog entry information

Last update

More entries in General

  • Recovered
    Hello! I haven’t posted in a bit! Kiwi has made a full recovery, and is...
  • Progress #3 (?)
    We did it everyone. she’s using her tongue and climbing all over the...
  • Progress #2
    Being honest here i feel like my work is doing nothing. like i started...
  • Progress #1
    Our helm has totally firmed! i’m so proud and i appreciate your...
  • Why Chameleons?
    Story time! I've wanted a chameleon ever since I knew you could own one...

More entries from Seeco

Top Bottom